Hot Air Bath (Underground, Above Ground all Size Possible)
<p class="stock in-stock"></p>
• The gap between the walls is filled up with special grade glass wool for proper
insulation to avoid heat losses.
• Temperature Control, Thermostat (Temperature accuracy +/- 3 Deg C)
• On/Off Control (Temperature accuracy +/- 2 Deg C)
• PID Control (Temperature accuracy +/- 1 Deg C)
• Microprocessor control (Temperature accuracy +/- 0.5 Deg C
• Please specify the kind of controller and accuracy required at the time of
ordering.
• Water Circulation
• Water circulation using separate motor or stirrer.
• Elements
• Heating elements are made of high quality heaters which are put inside the
water bath and placed at the bottom of the bath
Hot Air Bath | Hot Water Bath Apparatus
A Hot Air Bath is equipment that is used to incubate samples at a constant temperature over a long period of time. It is preferably used for heating flammable chemicals to prevent ignition. It is also used in the warming of reagents. melting of substrate and cell cultures etc. It has various uses in bacteriological and laboratory applications requiring incubation as well as general test procedures
Every Tech Trivial Hot Air Bath gives you exactly what you need: accurate measurements, consistent, reliable performance, best possible safety, and best possible warranty available.
Model No.: D1018
Features:
Temperature range: room temp. to 250 degree celsius
No. Of Shelves: 2
Portable: Yes
The gap between the walls is filled up with special grade glass wool for proper
insulation to avoid heat losses.
Temperature Control, Thermostat (Temperature accuracy +/- 3 Deg C)
On/Off Control (Temperature accuracy +/- 2 Deg C)
PID Control (Temperature accuracy +/- 1 Deg C)
Microprocessor control (Temperature accuracy +/- 0.5 Deg C
Please specify the kind of controller and accuracy required at the time of
ordering: Water Circulation, Water circulation using separate motor or stirrer, Elements
Heating elements are made of high-quality heaters which are put inside the
water bath and placed at the bottom of the bath
Standard double wall fabrication.
Specification:
It is customizable as per your need. Followings are available where chamber size in (ms/inches) and No. of shelves are given:
300 x 300 x 300 (12″ x 12″ x 12″ ): 2
275 x 400 x 275 (11″ x 16″ x 11″) : 2
350 x 350 x 350 (14″ x 14″ x 14″) : 2
400 x 400 x 400 (16″ x 16″ x 16″) : 2
600 x 600 x 600 (24″ x 24″ x 24″) : 2
900 x 600 x 450 (36″ x 24″ x 18″) : 2
900 x 600 x 600 (36″ x 24″ x 24″) : 2
900 x 900 x 900 (36″ x 36″ x 36″) : 2
450 x 450 x 450 (18″ x 18″ x 18″) : 2
600 x 450 x 450 (24″ x 18″ x 18″) : 2
You can also check out our more Machinery Products.
Hot Air Bath | Hot Water Bath Apparatus
Based on 0 reviews
Be the first to review “Hot Air Bath (Underground, Above Ground all Size Possible)”
You must be logged in to post a review.
Related products
-
Automated Testing, General & Physical Tests, Machinery
UV weathering test chamber as per ISO 4892 – XENON ARC
Automated Testing, General & Physical Tests, MachineryUV weathering test chamber as per ISO 4892 – XENON ARC
UV weathering test chamber as per ISO 4892-XENON ARC TEST EQUIPMENT generally compliant with HD 626-2 or ISO 4892-2
The test equipment consists of
- 1-piece water-cooled xenon lamp with inner quartz and outer borosilicate filter
- Programmable color display touch screen controller to control and display test parameters
- Measurement and control of irradiance value at both 340nm, and 300~400nm
- Measurement and control of Black Panel Temperature (BPT)
- Measurement and control of chamber temperature and chamber humidity
- A water spray system with a built-in 50L water reservoir
- An automatic water supply system
- Industrial control panel with ferrule numbering & professional wiring for easy maintenance and troubleshooting
- RS-232 interface, able to connect and programs with Industrial PC/Desktop PC/Laptop
please also check our Fluoroscent Lamp UV weathering test equipment for cost-effective version.
Xenon Arc Test or UV Weathering Test as per ISO 4892-2 & 3
SKU: n/a -
General & Physical Tests
Cold Bend Test | Cold Impact Test
IEC 60811-504 describes the cold bend test method for cables under low temperatures. The cold bend test on cable is only possible upto a maximum diameter of 12.5mm. The test is mainly conclusive to understand the flexibility and strength of plastic used over cable under low temperatures.
Whereas cold impact test on cables is performed according to IEC 60811-506. This test is mainly designed to simulate the plastic’s capacity to resist mechanical shock under cold environment.Here from a certain height, mandrels of specific weight are dropped on the cable.
SKU: n/a -
Automated Testing, General & Physical Tests, Machinery
Optical Profile Projector for cable
We have all range of Profile projectors suitable for cable and automotive manufacturing sector. Market is flooded with inaccurate and camera based profile projectors that are actually not compliant with Vision systems but still expansive as them.
Automatic profile projector for cable used in Cable Dimension measurement of any shape of the cable. Available with Accredited calibration master, color measurement, from 36 mm to 108 mm diameter samples.IEC-60502-1 and EN 50525 describes the requirement of exact dimension measurement of the insulation, inner jacket and outer jacket of a cable and it’s core.
Where you actually lose money?
- Having higher Insulation wall thickness due to the operator’s running safety margin
- Ovality of extrusion head setting causes the inhomogeneous spread of compound over the conductor.
- Due to higher core diameter, each next process of cable manufacturing such as stranding, taping, braiding, armoring, shielding, inner sheathing, outer jacketing takes a minimum of 0.05% to 3% of extra material.
- An average-sized Cable manufacturer who consumes 10 Million euros of plastics per year losses around 300.000 € just because of non-optimized dimension of cables.
We also supply all the measuring components calibrated by NABL accredited master instruments so that accuracy and uncertainty are never a concern for our clients.
SKU: n/a -
General & Physical Tests
Shore A and D – Hardness Tester
The hardness tester is used for understanding the suitability of plastic compound material such as PVC, LSZH, EVA, PE, etc.
The test itself becomes very important when it is crucial to decide the temperature profile and tensile strength required for the product in the design phase. The hardness of the compound also determines flexibility of cable up to some extent.
SKU: n/a
There are no reviews yet.