High Performance Insulation Resistance Tester
<p class="stock in-stock"></p>
Specifications:-
Warranty:-1 Year
Standard:-ASTM & UL Standards
Power supply:-220V (1±10%) / 50Hz (1±5%)
Material:-SUS 304 Stainless Steel
Application:-Electronic products, wire & cable
Model Number:-D580
Power:-Electronic
Power consumption:-≤ 40W
Weight:-About 5 KG
Voltage display accuracy:-± 1%
Product Description
IEEE43 High-Performance Insulation Resistance Tester
Introduction:-
KT720 and KT720A are measuring instruments dielectric materials, equipment insulation resistance testers for measuring the insulation and properties of electronic components, wires and cables.
| Technical indicators | |
| Model | KT720A KT720 |
| Set the measurement voltage | 10-1000V 10-500V |
| No-load output voltage | ± 1% Set voltage ± 1V |
| Voltage display accuracy | ± 1% |
| Resistance measurement range | 1 x 103Ω – 1 x 1012Ω 1 x 103Ω – 1 x 1011Ω |
| Resistance measurement accuracy | < 10GΩ ±3% ±3 words
≥ 10GΩ ±8% ±3 words |
| Range control | Automatic / manual |
| Measurement method | control single time Continuous/remote |
| Display mode Voltage | Four: four or five significant digits; resistance digits |
| Test speed | About 5-6 times / sec |
| Sorting preset range | 0-999999MΩ (0 is not sorted) 1 file sorting, 5 groups of memory |
| Sorting judgment | Pass/Fail |
| Signal Type | Qualified / Failed / Closed |
| Clear mode | Open circuit clear |
| Interface mode | Sorting output (pass/fail), remote control signal input (optional) |
| Weight about | 5Kg |
| Power consumption | ≤ 40W |
| Power supply | 220V (1±10%) / 50Hz (1±5%) |
| Warm-up time | About 15 minutes into the accuracy range |
Frequently Asked Questions:-
What is IEEE 43?
It is Testing Insulation windings in rotating machines recommended procedure for Resistance Recommended Practice for of Rotating Machinery. This of armature describes a document and field rated 750 W or greater.
Why is insulation resistance test carried out at 500V?
Remember this and there is also a risk of instrument that the insulation the conductors electric shock test can damage equipment from the deck voltage (usually 500v). We are testing to ensure and that there are no short is adequate circuits between surrounding produced by your test conductors.
What is high insulation resistance?
This voltage (usually 500V or more) through and on our would indicate a value over the insulation’s surfaces. Based small relatively low to flow value would point current causes a resistance discussion, a high “good” insulation while a to a “poor” insulation.
Related products
-
Electrical & Electronic
Continuity Voltage Tester
In Cable manufacturing at the final stage of testing, Continuity test is a standard practice and should be carried on each conductor. It is better to conduct Continuity test before HV test so that further damage of cable can be avoided in case the continuity is not shown by the conductor cores.
SKU: n/a -
Electrical & Electronic
IEC 60695 Horizontal and Vertical Flammability Testing Equipment For Plastics
Electrical & ElectronicIEC 60695 Horizontal and Vertical Flammability Testing Equipment For Plastics
Horizontal and Vertical Flammability Testing Equipment For Plastics is suitable for testing the resistance of plastics and their plastic parts to spread combustion under the condition of flame combustion. It is in line with standard requirements of GB/T2408, GB13488, ISO1210 and UL94.
SKU: n/a -
Electrical & Electronic
ISO 5659 Plastic Smoke Density Measuring Instrument
Plastic Smoke Density Measuring Instrument Smoke Density Tester is suitable for measuring the specific optical density of the smoke produced during the combustion of plastics. It is in line with standard GB/T8323.2-2008 “Plastic Smoke Generation-Part 2: Test Method for Measuring Smoke Density by Single Chamber Method”.
SKU: n/a
